Hyundai Accent Manuals

Hyundai Accent: Troubleshooting - General Information - Engine Mechanical SystemHyundai Accent: Troubleshooting

Hyundai Accent RB (2010-2018) Service Manual / Engine Mechanical System / General Information / Troubleshooting

Troubleshooting

Symptom
 Suspect area
 Remedy
Engine misfire with abnormal internal lower engine noises.
 Loose or improperly installed engine flywheel.
 Repair or replace the flywheel as required.
Worn piston rings.
(Oil consumption may or may not cause the engine to misfire.)
 Inspect the cylinder for a loss of compression .
Repair or replace as required.
Worn crankshaft thrust bearings.
 Replace the crankshaft and bearings as required.
Engine misfire with abnormal valve train noise.
 Stuck valves.
(Carbon buildup on the valve stem can cause the valve not to close properly.)
 Repair or replace as required.
Excessive worn or mis-aligned timing chain.
 Replace the timing chain and sprocket as required.
Worn camshaft lobes.
 Replace the camshaft and MLA.
Engine misfire with coolant consumption.
•
Faulty cylinder head gasket and/or cracking or other damage to the cylinder head and engine block cooling system.
•
Coolant consumption may or may not cause the engine to overheat.
•
Inspect the cylinder head and engine block for damage to the coolant passages and/or a faulty head gasket.
•
Repair or replace as required.
Engine misfire with excessive oil consumption.
 Worn valves, valve guides and/or valve stem oil seals.
 Repair or replace as required.
Worn piston rings.
(Oil consumption may or may not cause the engine to misfire)
 Inspection the cylinder for a loss of compression.
Repair or replace as required.
Engine noise on start-up, but only lasting a few seconds.
 Incorrect oil viscosity.
 Drain the oil.
Install the correct viscosity oil.
Worn crankshaft thrust bearing.
 Inspect the thrust bearing and crankshaft.
Repair or replace as required.
Upper engine noise, regardless of engine speed.
 Low oil pressure.
 Repair or replace as required.
Broken valve spring.
 Replace the valve spring.
Worn or dirty valve lifters.
 Replace the valve lifters.
Stretched or broken timing chain and/or damaged sprocket teeth.
 Replace the timing chain and sprockets.
Worn timing chain tensioner, if applicable.
 Replace the timing chain tensioner as required.
Worn camshaft lobes.
 Inspect the camshaft lobes.
Replace the camshaft and valve lifters as required.
Worn valve guides or valve stems.
 Inspect the valves and valve guides, then repair as required.
Stuck valves. (Carbon on the valve stem or valve seat may cause the valve to stay open.)
 Inspect the valves and valve guides, then repair as required.
Lower engine noise, regardless of engine speed.
 Low oil pressure.
 Repair or replace damaged components as required.
Loose or damaged flywheel.
 Repair or replace the flywheel.
Damaged oil pan, contacting the oil pump screen.
 Inspect the oil pan.
Inspect the oil pump screen.
Repair or replace as required.
Oil pump screen loose, damaged or restricted.
 Inspect the oil pump screen.
Repair or replace as required.
Excessive piston-to-cylinder bore clearance.
 Inspect the piston and cylinder bore.
Repair as required.
Excessive piston pin-to-bore clearance.
 Inspect the piston, piston pin and the connecting rod.
Repair or replace as required.
Excessive connecting rod bearing clearance.
 Inspect the following components and repair as required.
•
The connecting rod bearings.
•
The connecting rods.
•
The crankshaft.
•
The crankshaft journal.
Excessive crankshaft bearing clearance.
 Inspect the following components and repair as required.
•
The crankshaft bearings.
•
The crankshaft journals.
Incorrect piston, piston pin and connecting rod installation.
 Verify the piston pins and connecting rods are installed correctly.
Repair as required.
Engine noise under load.
 Low oil pressure.
 Repair or replace as required.
Excessive connecting rod bearing clearance.
 Inspect the following components and repair as required.
•
The connecting rod bearings.
•
The connecting rods.
•
The crankshaft.
Excessive crankshaft bearing clearance.
 Inspect the following components and repair as required.
•
The crankshaft bearings.
•
The crankshaft journals.
•
The cylinder block crankshaft bearing bore.
Engine will not crank. (crankshaft will not rotate)
 Hydraulically locked cylinder.
•
Coolant/antifreeze in cylinder.
•
Oil in cylinder.
•
Fuel in cylinder.
Remove spark plugs and check for fluid.
Inspect for broken head gasket.
Inspect for cracked engine block or cylinder head.
Inspect for a sticking fuel injector and/or leaking fuel regulator.
Broken timing chain and/or timing chain gears.
 Inspect timing chain and gears.
Repair as required.
Foreign material in cylinder.
•
Broken valve.
•
Piston material.
•
Foreign material.
Inspect cylinder for damaged components and/or foreign materials.
Repair or replace as required.
Seized crankshaft or connecting rod bearings.
 Inspect crankshaft and connecting rod bearing.
Repair or replace as required.
Bent or broken connecting rod.
 Inspect connecting rods.
Repair or replace as required.
Broken crankshaft.
 Inspect crankshaft.
Repair or replace as required.


Repair procedures
Compession Pressure Inspection If the there is lack of power, excessive oil consumption or poor fuel economy, measure the comp ...

Special Service Tools
Special Service Tools Tool (Number and name) Illustration Use Crankshaft front oil seal installer (09455-21200) Ins ...

See also:

Repair procedures
Inspection Manual Transaxle Oil Inspection 1. Park the vehicle on a level ground and stop the engine. 2. Retighten the oil f ...

Installation
1. Install the power window switch module. 2. Install the door trim panel after reconnecting the relevant connectors ...

Crankshaft Position Sensor (CKPS). Schematic Diagrams
Circuit Diagram (M/T) (A/T) ...

Hyundai Accent Manuals


© 2011-2024 Copyright www.hamanual.com