Hyundai Accent Manuals

Hyundai Accent: Installation - Parking Brake Assembly. Repair procedures - Parking Brake System - Brake SystemHyundai Accent: Installation

Hyundai Accent RB (2010-2018) Service Manual / Brake System / Parking Brake System / Parking Brake Assembly. Repair procedures / Installation

Rear Disc Brake Type
1.
Install the parking brake cable.
2.
Install the parking brake cable (A), and then install the clip (B).
3.
Install the rear tire and wheel.
4.
Install the parking brake lever assembly.

5.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
Specified grease:
Multi purpose grease SAE J310, NLGI No.2

6.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke:
5 ~ 7 clicks (Pull the lever with 196N (20 kgf, 44 lbf))
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

7.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
8.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
9.
Reconnect the connector (A) of parking brake switch.

Inspect the continuity of parking brake switch.
When the brake lever is pulled: continuity
When the brake lever is released: no continuity
10.
Install the floor console rear mounting bracket.
11.
Install the floor console. (Refer to Body group - "Floor console")
Rear Drum Brake Type
1.
Install the parking brake cable.
2.
Install the parking brake cable (A), and then install the clip (B).
3.
Remove the brake shoe. (Refer to the rear drum brake)
4.
Install the rear tire and wheel.
5.
Install the parking brake lever assembly.

6.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
Specified grease:
Multi purpose grease SAE J310, NLGI No.2

7.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke:
5 ~ 7 clicks (Pull the lever with 196N (20 kgf, 44 lbf))
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

8.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
9.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
10.
Reconnect the connector (A) of parking brake switch.

Inspect the continuity of parking brake switch.
When the brake lever is pulled: continuity
When the brake lever is released: no continuity
11.
Install the floor console rear mounting bracket.
12.
Install the floor console. (Refer to Body group - "Floor console")

Removal
Rear Disc Brake Type The parking brake cables must not be bent or distorted. This will lead to stiff operation and ...

Adjustment
Parking Brake Lever Stroke Adjustment 1. Remove the floor console. (Refer to Body group - "Floor console".) 2. R ...

See also:

Passenger and Rear Power Window Switch
...

Lift And Support Points
When heavy rear components such as suspension, fuel tank, spare tire, tailgate and trunk lid are to be removed, place additiona ...

Aux, USB and iPod® port
If your vehicle has an aux and/or USB(universal serial bus) port or iPod® port, you can use an aux port to connect audio devices and a USB port to plug in a USB, or use the HYUNDAI accessory iP ...

Hyundai Accent Manuals

© 2011-2026 Copyright www.hamanual.com