Hyundai Accent Manuals

Hyundai Accent: Troubleshooting - Lighting System - Body Electrical SystemHyundai Accent: Troubleshooting

Hyundai Accent RB (2010-2018) Service Manual / Body Electrical System / Lighting System / Troubleshooting

Troubleshooting

1.
The lamp switch inputs can be checked using the GDS.
2.
To check the input value of lamp switch, select option "Body Control Module".
3.
To consult the present input/output value of BCM, Select option "Current DATA". It provides information of BCM input/output conditions of door lock/unlock, lamp control and power window timer and etc.
4.
To check the input value of lamp switch in force mode, select option "Actuation Test of smart junction box".
Symptom
 Possible cause
 Remedy
One lamp does not light
(all exterior)
 Bulb burned out
 Replace bulb
Socket, wiring or ground faulty
 Repair if necessary
Head lamps do not light
 Bulb burned out
 Replace bulb
Head lamp fuse (10A) blown
 Check for short and replace fuse
Head lamp relay faulty
 Check relay
Lighting switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Tail lamps and license plate lamps do not light
 Bulb burned out
 Replace bulb
Tail lamp fuse (10A) blown
 Check for short and replace fuse
Tail lamp relay faulty
 Check relay
Lighting switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Stop lamps do not light
 Bulb burned out
 Replace bulb
Stop lamp fuse (15A) blown
 Check for short and replace fuse
Stop lamp switch faulty
 Adjust or replace switch
Wiring or ground faulty
 Repair if necessary
Stop lamps do not turn off
 Stop lamp switch faulty
 Repair or replace switch
Instrument lamps do not light
(Tail lamps light)
 Wiring or ground faulty
 Repair if necessary
Turn signal lamp does not flash on one side
 Bulb burned out
 Replace bulb
Turn signal switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Turn signal lamps do not light
 Bulb burned out
 Replace bulb
Turn signal lamp fuse (15A) blown
 Check for short and replace fuse
Flasher unit faulty
 Check flasher unit
Turn signal switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Hazard warning lamps do not light
 Bulb burned out
 Replace bulb
Hazard warning lamp fuse (15A) blown
 Check for short and replace fuse
Flasher unit faulty
 Check flasher unit
Hazard switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Flasher rate too slow or too fast
 Lamps' wattages are smaller or larger than specified
 Replace lamps
Flasher unit faulty
 Check flasher unit
Side marker lamps do not ligth
 Bulb burned out
 Replace bulb
Turn signal lamp fuse(15A) blown
 Check for short and replace fuse
Back up lamps do not light
 Bulb burned out
 Replace bulb
Back up lamp fuse (10A) blown
 Check for short and replace fuse
Back up lamp switch (M/T) faulty
 Check switch
Transaxle range switch (A/T) faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Front fog lamps do not light
 Bulb burned out
 Replace bulb
Front fog lamp fuse (10A) blown
 Check for short and replace fuse
Front fog lamp relay faulty
 Check relay
Front fog lamp switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Room lamp does not light
 Bulb burned out
 Replace bulb
Room lamp fuse (10A) blown
 Check for short and replace fuse
Map lamp switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary
Luggage room lamp does not light
 Bulb burned out
 Replace bulb
Room lamp fuse (10A) blown
 Check for short and replace fuse
Luggage room lamp switch faulty
 Check switch
Wiring or ground faulty
 Repair if necessary


Installation
1. Install the rear combination lamp assembly. 2. Connect the rear combination lamp assembly connector. 3. Conn ...

Immobilizer System
...

See also:

Side Impact Sensor (SIS). Description and Operation
Description The Side Impact Sensor (SIS) system consists of two front SIS which are installed inside the Center Pillar (LH and RH). They are remote sensors that detect acceleration due to co ...

Removal
Pressure Side Impact Sensor • Removal of the airbag must be performed according to the ...

Removal
1. Disconnect the vapor hose (A). 2. Remove the PCV valve (B). ...

Hyundai Accent Manuals


В© 2011-2024 Copyright www.hamanual.com